REVOLABS FLX2TM Wireless Conference System for analog phone lines System Guide Models: 10-FLX2-200-POTS 10-FLX2-020-POTS 10-FLX2-002-POTS
10 Installing FLX2 Components The Revolabs FLX2TM System is comprised of several components that work together to provide you with a great wireless c
11 FLX2 Charger Base The FLX2 Charger Base, shown below, provides charging capabilities for all battery operated system components, including the Dia
12 FLX Dialer The FLX Dialer equips the user with an intuitive and interactive tool for configuring and operating the FLX System. The Dialer is not
13 FLX Speaker The FLX Speaker, shown below, is a wireless active omnidirectional speaker that has been designed and optimized specifically for use w
14 FLX Microphones The FLX Microphones provide a sleek and unobtrusive form factor allowing for closer proximity to the participants and creating the
15 Initial Setup After unpacking the FLX2 Conferencing System, there are a few initial setup tasks that must be performed before a call can take plac
16 Handset Mode Handset mode allows a telephone call to take place through the handset speaker and microphone located in the FLX Dialer. This allows
17 Placing a Telephone Call 1. From the home screen on the FLX Dialer enter the phone number to be called. 2. Once the number is entered completel
18 Ignoring an Incoming Telephone Call 1. When the FLX2 System identifies an incoming call, it will play the ring tone through the FLX Speaker. 2.
19 Active Call Management The FLX2 System has many call features that can be used when receiving or making phone calls. These features can be control
2 © 2011 REVOLABS, INC. All rights reserved. No part of this document may be reproduced in any form or by any means without exp
20 Placing a Call on Hold 1. Access Active Call Menu by pressing the ‘Enter’ key during a call. Select menu item ‘Hold’. 2. To resume the call pres
21 Charging Components during a Call Each system component will respond differently when placed in or out of the charger during an active telephone c
22 Managing the Device Registry The FLX2 Bluetooth interface has a device registry where it activates, stores and recalls 3rd party Bluetooth devices
23 Viewing Device Details 1. Go to the Menu Bluetooth. Select ‘Device List’. 2. Select desired device and press the ‘Enter’ key or the ‘Select’ ke
24 Making a call via Bluetooth 1. With the Bluetooth connection enabled, dial a number from the Bluetooth device. The call will be conducted using t
25 FLX2 System Configuration There are many features to the FLX2 System that can be modified and configured using the FLX Dialer. The following is a
26 Recent Calls The Recent Calls call log stores the contact information from calls placed or received, allowing the user to review recent calls, red
27 View Recent Call Information 1. Access the recent call log by browsing: Menu Recent Calls or pressing the green ‘Call’ button while no call is
28 Delete Call History 1. Access the recent call log by browsing: Menu Recent Calls or pressing the green ‘Call’ button while no call is in progre
29 Add a Contact 1. Browse to the Contacts menu: Menu Contacts. 2. Press the ‘New’ key to create a new contact. 3. Edit the name in alphanumeric
3 Introduction Congratulations on your purchase of the Revolabs FLX2TM Wireless Conference Phone. This system utilizes state of the art technology p
30 Search for Contact 1. Browse to the Contacts menu: Menu Contacts. 2. Use the keys (0-9) to apply a filter a. Once a key is pressed the title
31 Set Speed Dial 1. Browse to the Contacts menu: Menu Contacts, scroll to the desired contact, and selects the ‘View’ key to access the contact.
32 Ringer 1. Browse to the Ringer menu: Menu Audio Controls Ringer. 2. Choose ‘Ringer Volume’ in the Ringer Settings menu to adjust the Ringer
33 Device Status 1. Browse to Device Status: Menu Device Status. 2. The Device Status screen shows status for the Microphones and the Speaker.
34 Call When selecting ‘Call’ in the menu, the Dialer will open the Dialer menu, allowing dialing a number. Setup Setup is divided into a generic are
35 Advanced Setup The following is a list of advanced configuration settings that are protected by a 4 digit password for administrator access only.
36 Setting System Name 1. Go to Menu Setup Advanced Setup Admin Settings Set System Name. 2. Change the current System Name to the new name,
37 Pairing All FLX2 wireless components are paired before the system is shipped, providing much of the system setup already completed. While pairing
38 that the pairing failed. The Dialer will display a ‘Pairing Timeout’ message. In that case the pairing procedure should be repeated. Microphone
39 Power On/Off the System Components During normal use and operation of the FLX2 System, there is no need to turn off any part of the system. Howeve
4 Contents Introduction ...
40 Troubleshooting Warning Messages Speaker/Microphone Link Lost If a FLX Microphone or FLX Speaker loses connection to the FLX2 Base Station, the LE
41 2. The Base Station is powered up, but the Status LED indicates a fault by missing every fifth green double flash. Power down and power up the B
42 LED Indicators Device LED Indicator Status Microphone in Charger Base Steady Red Charging Steady Green Fully charged Off Microphone is powered off
43 Device LED Indicator Status “All Mic Mute” is ON, all microphones muted Flashing Yellow* – Red – Yellow* – Green Searching for a connection to the
44 Technical Specifications Models The Revolabs FLX2 System is available with a variety of configurations to provide the best audio capture in the in
45 Microphones Dimensions Microphones 94.2 x 24.6mm x 18.5mm (omnidirectional Microphone) Weight 28.6g (omnidirectional Microphone) Bandwidth 80-1
46 Regulatory Information FCC Notice to Users Users are not permitted to make changes or modify the equipment in any way. Changes or modifications no
47 Restricted use with certain medical devices Hearing Aids Some devices may interfere with some hearing aids. In the event of such interference, you
48 E C Declaration of Conformity Manufacturer’s Name: Revolabs Manufacturer’s Address: 144 North Road, Suite 3250 Sudbury, MA 01776 U.S.A. Mo
49 ACTA Part 68 information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the base of this e
5 Home ...
50 Warranty Limited Warranty Revolabs warrants to the end user (“Customer”) that this product will be free from significant defects in workmanship a
51 Disclaimer Some countries, states, or provinces do not allow the exclusion or limitation of implied warranties or the limitation of incidental or
6 General Information The Revolabs FLX2 Conference Phone includes several components which, in the sum, make up the conferencing phone. The componen
7 Quick setup for Telephone Conference Calls While all components delivered with the Revolabs FLX2 Conference Phone are partially charged, we recomm
8 Making a call To make a conference call, take at least one of the Microphones out of the Charger Base, and take the Dialer out of the Charger Base.
9 Description The Revolabs FLX2™ Wireless Conference Phone is a unique marriage of innovative technology and ergonomic design, allowing for an unpara
Commentaires sur ces manuels